Каталог запасных частей роторной дробилки SANDVIK CV228

Деталь №;Описание

488.0003-901; Crushing chamber 488.0205-901; Base 488.1353-901; Support frame assembly 488.0146-901; Drive unit 488.0461-901; Top 488.1672-901; VSI Feed kit assembly 906.0477-00; Hydraulic unit 488.0460-901; Protection assembly 488.0924-901; Bottom taper assembly 488.0506-901; Grease unit 881.0190-00; Interlock kit, mechanical 488.0508-901; Tool box 488.0175-901; Rotor lifting tool 488.1808-901; Hydraulic cabin 488.1481-901; Parts in crushing chamber CV228 488.1663-901; Sign board assembly 845.0203-00; Nut Lock ISO 7040 M20 8 FZB 847.0132-00; Washer round 21x36 ZP 840.0650-00; Screw M6S M20x65 8.8 ZP 488.0113-901; Bearing house assembly 488.1302-901; Non stick transmission liners 488.1207-901; Motors 488.1367-901; Water spray unit 488.1384-901; Platform assembly 488.1151-901; Grease 488.1355-901; Dust protection complete 488.1788-901; VSI Rotor 85HP, alt. 488.0372-901; Rotor balance machine 488.1225-901; Skid frame 488.1413-901; Legs 488.1208-901; VSI Drive alt. 488.1822-901; VSI Set biflow liners 488.0134-901; Crushing chamber 488.0118-901; Inspection door assembly 488.0320-001; Rubber capping U13/17 488.1756-901; VSI Cavity ring 488.1760-901; VSI Cavity ring 840.0079-00; Screw M6S 20x70 8.8 ISO 4017 847.0132-00; Washer round 21x36 ZP 845.0203-00; Nut lock ISO 7040 M20 8 FZB 840.0669-00; Screw M6S 24x70 8.8 ISO 4017 847.0124-00; Washer BRB 25x45 ZP 845.0387-00; Nut lock ISO 7040 M24 8 FZB 488.0072-001; Swingbolt 488.0073-001; Swingbolt - pin 488.0296-001; Bolt 855.0224-00; Circlip for shaft 9 SMS 1583 A2 488.0115-001; Stop plate 488.1740-901; VSI Clamp washer 488.0270-001; Wedge 488.1747-001; VSI Washer 488.1751-001; VSI Bracket 840.0653-00; Screw M6S 20x100 8.8 ISO 4014 488.0181-901; Door cavity ring 488.0119-901; Door 488.0125-901; Door hinge frame 488.0136-001; Hinge pin 488.0135-901; Door handle 488.0139-001; Safety pin 488.0143-001; Door lug bracket 488.0144-001; Door lug bracket 488.0145-001; Hinge pin 840.0078-00; Screw M6S M20x60 8.8 ZP 847.0132-00; Washer round 21x36 ZP 855.0225-00; Retaining ring SgA 40 ZP 847.0171-00; Washer BRB 43x80 ZP 914.0090-00; Lubrication nipple AH R 1/8” 488.0404-001; V-block 840.0239-00; Screw MC6S M8x40 8.8 ZP 853.0262-00; Split pin SP 6,3x40 ZP 488.0454-901; Locking handle 847.0165-00; Washer TBRB 21x37 ZP 841.0222-00; Screw MC6S M6x30 8.8 ZP 861.0006-00; Spring Dt2,5xDi22,5xL115 877.0400-00; Chain stainless steel 6 mm 840.0049-00; Screw M6S M12x50 8.8 ZP 847.0014-00; Washer BRB 12x22 ZP 845.0030-00; Lock nut M12 8 ZP 488.1172-901; Toe board ring 840.0048-00; Screw M6S 12x45 8.8 ISO 1417 847.0147-00; Washer BRB 13x24 HB200 ISO 7089 845.0030-00; Lock nut M12 8 FZB ISO 7040 488.1176-001; Gusset 845.0203-00; Nut lock M20 8 FZB ISO 7040 840.0649-00; Screw M6S 20x55 8.8 FZB ISO 4017 847.0132-00; Washer round 21x36 ZP 488.0247-901; Motor bracket 2 488.0007-901; Motor bracket 488.0344-001; Tension plate 840.0647-00; Screw M6S 24x120 8.8 ISO 4014 847.0124-00; Washer BRB 25x45 HB200 845.0387-00; Nut Lock ISO 7040 M24 8 fzb 840.0670-00; Screw M6S 24x80 8.8 ISO 4017 488.0516-001; Motor cover 840.0044-00; Screw M6S 12x25 8.8 ISO 4017 847.0059-00; Washer TBRS 13.5x36 488.0294-001; Bolt 853.0997-00; Clips R-clips type A E4 488.0113-901; Standard 488.0113-902; High temperature 853.0603-00; Pin Prym N 10x28 841.0416-00; Screw MF6S 8x25 8.8 488.0297-001; Top key 840.0657-00; Screw M6S 20x150 8.8 FZB ISO 4014 847.0132-00; Washer BRB 21x36 845.0203-00; Nut lock ISO 7040 M20 8 FZB 840.0073-00; Screw M6S 16x75 8.8 ISO 4014 847.0036-00; Spring washer FBB 16.2 488.0299-001; Bottom key 4488.1840-901; Base 488.0109-001; Discharge plate 488.0141-001; Liners 488.0318-001; Liners 488.0315-001; Gusset wear casting 488.0505-001; Vibration damper 847.0147-00; Washer BRB 13x24 HB200 ISO 7089 847.0124-00; Washer BRB 25x45 HB200 SS 3576 845.0387-00; Nut lock ISO 7040 M24 8 FZB 840.0678-00; Screw M6S 24x160 8.8 ISO 4014 840.0049-00; Screw M6S 12x50 8.8 ISO 4014 845.0030-00; Lock nut M12 8 FZB ISO 7040 853.0997-00; Clips R-clips type A E4 847.0132-00; Washer BRB 21x36 HB200 SS 3576 845.0203-00; Nut lock ISO 7040 M20 8 FZB 840.0532-00; Screw M6S 20x110 8.8 ISO 4014 488.0288-901; Cover 840.0076-00; Screw M6S M20x40 8.8 FZB ISO 4017 488.0286-001; Perforated plate 847.0144-00; Washer BRB 10,5x22 HB200 SS 3576 840.0033-00; Screw M6S 10x20 8.8 ISO 4017 847.0016-00; Washer BRB 17x30 HB200 ISO 7089 840.0070-00; Screw M6S 16x60 8.8 FZB ISO 4017 845.0215-00; Nut lock ISO 7040 M16 8 FZB 840.0064-00; Screw M6S M16x30 FZB ISO 4017 984.1159-00; Pre start sounder kit 984.1160-00; Vibration protection 843.1579-00; Screw ECS 5x12 8.8 ISO 1207 900.1139-00; Clip RSGU 1.22/15 840.0014-00; Screw M6S M6x30 8.8 FZB ISO 4014 845.0217-00; Nut lock ISO 7040 M6 8 FZB 488.0314-901; Grease duct 488.0313-001; Grease chute 488.1311-901; Wedge 840.0069-00; Screw M6S 16x55 8.8 ISO 4017 840.0622-00; Screw M6S 12x20 ISO 4017 488.1676-001; Ring 488.1673-901; VSI Feed kit assembly 488.0258-001; Feed tube 488.0270-001; Wedge 488.1677-901; Plate 845.0010-00; Nut M6M M20 8 FZB ISO 4032 488.0499-901; Chain HLZ 5.5mm SMS 1507 840.0078-00; Screw M6S 20x60 8.8 ISO 4017 840.0653-00; Screw M6S 20x100 8.8 ISO 4014 488.1679-901; Hatch 488.1624-901; Locking plate 488.1671-001; Bolt 845.0203-00; Nut lock ISO 7040 M20 8 FZB 488.0219-901; High profile rotor body 488.0029-001; Taper lock 488.0361-901; Lower wear plate set 488.0360-901; Upper wear plate set 488.0076-001; Distributor plate 488.1513-901; Distributor locating pin set 488.1644-901; Cavity wear plate set Turbo (upper) 488.1703-901; Cavity wear plate set Turbo (middle) 488.1704-901; Cavity wear plate set Turbo (lower) 488.0362-901; Trail plate 330 set 488.1456-901; Turbo tip set 110 mm (hard) 488.0368-901; Backup tip set 488.0369-901; Top wear plate set 840.0077-00; Screw M6S 20x50 8.8 ISO 4017 841.0502-00; Screw MC6S 24x60 12.9 488.0841-001; Top plate 488.0017-901; Roof 488.0031-901; Hopper 488.0104-901; Trottle 488.0282-901; Cover 488.0083-001; Plate d=340 488.0165-001; Cover 488.0293-001; Bolt 488.0292-001; Bolt 853.0997-00; Clips R-Clips Typ W E4 488.0484-001; Plate d=280 488.0485-001; Plate d=220 840.0622-00; Screw M6S M12x20 8.8 ZP Pt. 488.1325-001; Gasket 488.1326-001; Cover 840.0020-00; Screw M6S M8x16 8.8 ZP Pt. 847.0012-00; Washer BRB 8,4x16 ZP Pt. 488.0147-901; Protection 488.0192-901; Protection 488.0429-901; Cover 488.0285-001; Perforated plate 840.0033-00; Screw M6S 10x20 8.8 ISO 4017 847.0144-00; Washer BRB 10,5x22 HB200 SS 3576 840.0037-00; Screw M6S 10x35 8.8 ISO 4017 845.0213-00; Nut Lock ISO 7040 M10 8 FZB 488.0500-001; Edge list 914.0206-00; Grease unit keg mounted 825.0148-00; Grease firetemp XT2 825.0143-00; Grease long time PD2 904.0545-00; Grease hose L=600 904.0543-00; Grease hose L=1280 904.0542-00; Grease hose L=550 902.1104-00; Valve distributor 902.1105-00; Cycle indicator for valve distributor 2 906.0478-00; Hand pump GLA-25-4L 912.0214-00; Return filter MF-BN-80-GA-010-E1 902.0947-00; Pump valve HDM11S/3K04150AAA03L100 908.0471-00; Cylinder 25CA-R50/30-200/85 908.0470-00; Cylinder 25CA-VR-65/35-250/85 912.0213-00; Air filter UC-SAB-3101-R1/4 904.0434-00; 812-06 KL=450 904.0435-00; 812-06 KL=942 904.0436-00; 812-06 KL=1300 904.0437-00; 812-06 KL=500 904.0438-00; 812-06 KL=3100 904.0439-00; 812-06 KL=640 904.0440-00; 812-06 KL=1570 488.0474-901; Hydraulic plate 904.0442-00; Hose L=1950 904.0441-00; Hose L=900 881.0191-00; Bolt interlock 881.0185-00; Spacer for MLH-Q1058 881.0192-00; Time delay unit 881.0174-00; Sealed key C and D 881.0173-00; Heavy duty access interlock 881.0175-00; Dust cap 488.0002-901; Frame 488.0157-901; Leg gusset 488.0162-901; Leg gusset 488.0196-901; Cylinder bracket 488.0200-901; Cylinder bracket 488.0294-001; Bolt 840.0649-00; Screw M6S 20x55 8.8 ISO 4017 847.0132-00; Washer BRB 21x36 HB200 SS 3576 845.0010-00; Nut M6M M20 8 FZB ISO 4032 840.0650-00; Screw M6S 20x65 8.8 ISO 4017 488.0322-901; Transport leg 840.0652-00; Screw M6S 20x90 8.8 ISO 4017 488.0300-901; Skid frame 840.0649-00; Screw M6S 20x55 8.8 ISO 4017 8445.0010-00; Nut M6M 8 FZB ISO 4032 847.0132-00; Washer BRB 21x36 HB200 488.0107-901; Leg (1900 mm/74.8”) 488.0092-901; Leg (1900 mm/74.8”) 840.0650-00; Screw M6S 20x65 8.8 ISO 4017 847.0132-00; Washer BRB 21x36 HB200 SS 3576 845.0203-00; Nut lock ISO 7040 M20 8 fzb 488.0495-901; Leg (2670 mm/105.1”) 488.0496-901; Leg (2670 mm/105.1”) 840.0650-00; Screw M6S 20x65 8.8 ISO 4017 847.0132-00; Washer BRB 21x36 HB200 SS 3576 845.0203-00; Nut lock ISO 7040 M20 8 fzb 488.0383-001; Gable plate 488.0383-001; Distance plate 868.0138-00; Deep groove ball bearings SKF 6210 488.1315-901; Rotor balance shaft improved 488.0384-001; Clamp plate 847.0016-00; Washer BRB 17x30 HB200 ISO 7089 845.0009-00; Nut M6M M16 8 fzb ISO 4032 840.0067-00; Screw M6S 16x45 8.8 ISO 4017 840.0651-00; Screw M6S 20x75 8.8 ISO 4014 847.0132-00; Washer BRB 21x3 Hb200 SS 3576 845.0010-00; Nut M6M M20 8 FZB ISO 4032 840.0648-00; Screw M6S M20x45 8.8 FZB ISO 4017 488.0175-901; Plate 842.0311-00; Hex socket set screw T6SS 20x70 126.0384-001; Warning flying fragments 126.0320-001; Warning sign “Do not open...” 126.0323-001; Direction of rotation 126.0318-001; Warning sign “Do not attempt...” 885.0261-00; Lift here/ Secure here 126.0465-001; VSI Sign produkt name 126.0383-001; Risk of crushing 126.0386-001; Do not remove guards 126.0446-001; SANDVIK logotype silver 160 126.0385-001; Warning sign Read manual 126.5007-001; Identification plate 126.0327-001; VSI Hydraulic motor 1 126.0328-001; VSI Hydraulic motor 2 126.0329-001; VSI Hydraulic rotor 126.0326-001; VSI Hydraulics dual drive 126.0324-001; Grease supply 126.0335-001; Warning sign Do not remove bolts 885.0267-00; Warning sign Danger 488.0508-901; Tools 920.0275-00; Belt tensioning gauge 920.0274-00; Hex. bit 14mm 920.0273-00; Hex. bit 12mm 966.3421-00; Extension 1/2” 255mm 966.3420-00; Sliding T-bar 1/2” 300mm 920.0272-00; Spanner 30mmx36mm 920.0271-00; Spanner 17mmx19mm 966.3419-00; Combination spanner 24mm 920.0270-00; 1/2” drive socket 30mm 920.0269-00; 1/2” drive socket 24mm 920.0268-00; 1/2” drive socket 19mm 921.2042-00; Screwdriver 1.6x9 150mm 921.2041-00; Ball pein hammer 488.0509-001; Tool list 488.1682-001; Tool box 920.0276-00; 1/2” drive socket 18mm 920.0277-00; Hex. bit 8mm 920.0278-00; Hex. bit 10mm 920.0279-00; Hex. bit 19mm 920.0280-00; 3/4” drive socket 36mm 920.0281-00; 3/4” T-Bar 920.0282-00; Extension 3/4” 400mm